Àû²©¡¤(¼¯ÍÅ)ÓÐÏÞ¹«Ë¾¹ÙÍø

General Description

Introduction

The MC68HC908GR16A is a member of the low-cost, high-performance M68HC08 Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the enhanced M68HC08 central processor unit (CPU08) and are available with a variety of modules, memory sizes and types, and package types.

Features

For convenience, features have been organized to reflect:

? Standard features

? Features of the CPU08

Standard Features

Features include:

? High-performance M68HC08 architecture optimized for C-compilers

? Fully upward-compatible object code with M6805, M146805, and M68HC05 Families

? 8-MHz internal bus frequency

? Clock generation module supporting 1-MHz to 8-MHz crystals

? FLASH program memory security(1)

? On-chip programming firmware for use with host personal computer which does not require high voltage for entry

? In-system programming (ISP)

? System protection features:

¨C Optional computer operating properly (COP) reset

¨C Low-voltage detection with optional reset and selectable trip points for 3.3-V and 5.0-V operation

¨C Illegal opcode detection with reset

¨C Illegal address detection with reset

? Low-power design; fully static with stop and wait modes

? Standard low-power modes of operation:

¨C Wait mode

¨C Stop mode

? Master reset pin and power-on reset (POR)

? 16 Kbytes of on-chip FLASH memory

? 1 Kbyte of on-chip random-access memory (RAM)

? 406 bytes of FLASH programming routines read-only memory (ROM)

? Serial peripheral interface (SPI) module

? Enhanced serial communications interface (ESCI) module

? Fine adjust baud rate prescalers for precise control of baud rate

? Arbiter module:

¨C Measurement of received bit timings for baud rate recovery without use of external timer

¨C Bitwise arbitration for arbitrated UART communications

? LIN specific enhanced features:

¨C Generation of LIN 1.2 break symbols without extra software steps on each message

¨C Break detection filtering to prevent false interrupts

? Two 16-bit, 2-channel timer interface modules (TIM1 and TIM2) with selectable input capture, output compare, and pulse-width modulation (PWM) capability on each channel

? Up to 8-channel, 10-bit successive approximation analog-to-digital converter (ADC) depending on package choice

? BREAK (BRK) module to allow single breakpoint setting during in-circuit debugging

? Internal pullups on IRQ and RST to reduce customer system cost

? Up to 37 general-purpose input/output (I/O) pins, including:

¨C 28 shared-function I/O pins

¨C Up to nine dedicated I/O pins, depending on package choice

? Selectable pullups on inputs only on ports A, C, and D. Selection is on an individual port bit basis. During output mode, pullups are disengaged.

? High current 10-mA sink/source capability on all port pins

? Higher current 20-mA sink/source capability on PTC0¨CPTC4

? Timebase module (TBM) with clock prescaler circuitry for eight user selectable periodic real-time interrupts with optional active clock source during stop mode for periodic wakeup from stop using an external crystal

? User selection of having the oscillator enabled or disabled during stop mode

? Up to 8-bit keyboard wakeup port depending on package choice

? 2 mA maximum current injection on all port pins to maintain input protection

? Available packages:

¨C 32-pin quad flat pack (LQFP)

¨C 48-pin quad flat pack (LQFP)

? Specific features of the MC68HC908GR16A in 32-pin LQFP are:

¨C Port A is only 4 bits: PTA0¨CPTA3; 4-pin keyboard interrupt (KBI) module

¨C Port B is only 6 bits: PTB0¨CPTB5; 6-channel ADC module

¨C Port C is only 2 bits: PTC0¨CPTC1

¨C Port D is only 7 bits: PTD0¨CPTD6; shared with SPI, TIM1, and TIM2 modules

¨C Port E is only 2 bits: PTE0¨CPTE1; shared with ESCI module

? Specific features of the MC68HC908GR16A in 48-pin LQFP are:

¨C Port A is 8 bits: PTA0¨CPTA7; 8-pin KBI module

¨C Port B is 8 bits: PTB0¨CPTB7; 8-channel ADC module

¨C Port C is only 7 bits: PTC0¨CPTC6

¨C Port D is 8 bits: PTD0¨CPTD7; shared with SPI, TIM1, and TIM2 modules

¨C Port E is only 6 bits: PTE0¨CPTE5; shared with ESCI module