利博·(集团)有限公司官网

Features

? True multi-touch

– Independent XY tracking with 10 simultaneous touches in real time

– Supports 21TX and 40RX channels and 1 FLOAT pin

? Single chip solution

– Supports 5.5 inch to 7 inch screen size with 4mm sensor pitch

– Supports thin flexible touch-display highly capacitive panel types

– Supports LTPO display panels with dynamic refresh rates

? Advanced Analog Front End (AFE)

– Simultaneous mutual sensing and self-sensing support on all the channels

– Support for thin flexible touch display modules through proprietary node

compensation hardware

– Differential architecture with ability to configure in single-ended mode

– Multiple scanning methods with multi-TX drive for high SNR and provide

high noise immunity

– High drive capability charge-pump to drive high capacitive panels

? High SNR

– Very low intrinsic noise to improve the device SNR and provide very high

sensitivity

– Extremely strong common mode charger noise rejection

– Advanced filtering techniques for high noise immunity

? SYNC support

– Supports SYNC Mode and Non-SYNC Mode of operation

– Supports single SYNC pin that can be used as VSYNC, HSYNC or

Embedded VSYNC

– Useful for quad high definition display synchronization during both mutualsensing

and self-sensing

– Seamless support of variable display rate from 1Hz to 120Hz

? Digital Core and Memory

– ARM M4 core 96MHz core clock to implement all features with faster

processing

– 192KB Flash with GPIO6 dedicated pin for Flash Write enable for TEE

framework

– Advanced differential data processing for common mode noise immunity

– 128KB RAM comprised of 64KB frame memory and 64KB data)

? Advanced Features

– Multi finger thick gloves, 2.5mm passive stylus, wet finger touch, water

rejection, cover mode support

– Finger separation ≤ 10mm

– Capacitive proximity of 20mm

? Fast report rate

– Flexible Report rate of 240Hz

? Low Power

– ST proprietary Hardware and Firmware techniques to achieve low power

? Touch panels

– Works with thin flexible flat or curved panels with touch embedded into high resolution displays

– Works with LTPO display panels

? Power supply scheme

– Dual supply operation 3.3 V and 1.8 V

? Serial interface

– I2C compatible slave mode (100Kbps, 400Kbps, 1Mbps)

– 3-wire and 4-wire Mode 0 SPI interface 12MHz (typ.)

– 3.3V tolerant interface for I2C and SPI

– I/Os: RESETB, INTB hardware pins to host interface, 4 Digital inputs and 2 GPIOs with full

programmability

– All digital pins are fail safe

? ESD & TLP

– High ESD on RX and TX pins (±8KV HBM) and >±3KV HBM on all other pins

– High ESD on RX and TX pins (±1KV CDM) and ±500V CDM on all other pins

– >4A TLP on all pins

? EMI

– Low EMI <-70dBm average

– Flicker avoidance techniques

Description

The FingerTip FTG2-SLP provides an optimal mix of low power, small size, low external part counts and versatile

features with unmatched true multi-touch performance in a single-chip touchscreen controller for thin flexible

embedded display-touch panels.

The FingerTip FTG2-SLP uses a dedicated differential architecture with capacitance to current acquisition engine

to implement the touch sensing. Coupled with the internal processor the Fingertip touchscreen controller can

detect, classify and track 10 fingers touch with fast report rate and response times with a configurable channel

matrix consisting of total 21 TX and 40 RX channels.

The touch acquisition analog front end has a wide dynamic range able to cope with panels of different size

and configuration. This offers great flexibility to use FingerTip with new technology of embedded display-touch

panels that are thinner and flexible. The FingerTip FTG2-SLP provides support for flat or curved displays through

proprietary differential and node compensation hardware coupled with differential data processing techniques in

firmware.

The FingerTip FTG2-SLP low-noise differential capacitive analog front-end provides enhanced noise suppression

capabilities for various noise sources such as high resolution display, 3-phase noise and severe common mode

noise introduced by battery chargers.

The FingerTip FTG2-SLP uses hardware and firmware ST proprietary techniques to reduce power in active and

idle modes.

The FingerTip FTG2-SLP device incorporates multiple TX driving methods that can further boost the SNR and

report rate.

The FingerTip FTG2-SLP supports advanced features thanks to the multi-mode sensing technology. The water

rejection algorithm can detect water on the top of the screen and the device can still track one finger moving in the

water without false touch or line breaking. The device supports multi finger glove operation and 2.5mm passive

stylus. The device supports 20mm stable capacitive proximity.

Application

? Smartphones

? Phablets

? Foldable phones